Iai-america XSEL-S Uživatelský manuál

EtherNet/IPOperation Manual Second Edition‒XSEL-R/S/RX/SX/RXD/SXDIAI America, Inc.

4No.Operation Description Description 4 Installation and Start (4) Safety Measures Ɣ When the work is carried out with 2 or more persons, make it cl

5No.Operation Description Description 6 Trial Operation Ɣ When the work is carried out with 2 or more persons, make it clear who is to be the leader

6No.Operation Description Description 8 Maintenance and InspectionƔ When the work is carried out with 2 or more persons, make it clear who is to be

7Alert Indication The safety precautions are divided into “Danger”, “Warning”, “Caution” and “Notice” according to the warning level, as follows, and

8Caution in Handling 1. It is recommended that the baud rate be set based on auto negotiation. Make sure the link setting of the EtherNet/IP unit matc

1. Overview91. Overview EtherNet/IP is an open field network. It is a standardized global open network specified by the IEC 61158 series of internati

2. EtherNet/IP Specications102. EtherNet/IP Specifications Item Description Device Type Generic Device IP Address 1.0.0.1 to 255.255.255.254(Note 2

3. XSEL-R/S/RX/SX/RXD/SXD11 3. XSEL-R/S/RX/SX/RXD/SXD 3.1 Operation Modes and Functions XSEL Controllers applicable for EtherNet/IP are applicable f

3. XSEL-R/S/RX/SX/RXD/SXD123.2 Model The model code of each of XSEL-R/S/RX/SX/RXD/SXD applicable for EtherNet/IP is as shown below. Ɣ XSEL-R-Ƒ-EP-Ƒ

3. XSEL-R/S/RX/SX/RXD/SXD133.3 EtherNet/IP Interface 3.3.1 Names of the Parts 3.3.2 Monitor LED indications LED ColorIndication Status Meaning Illu

3. XSEL-R/S/RX/SX/RXD/SXD143.4 Wiring 3.4.1 Wiring (example) PLC (EtherNet/IP Master Unit) * Ethernet Cable: Straight cable of category 5 or more,

3. XSEL-R/S/RX/SX/RXD/SXD153.5 Setting Set to the I/O parameters in the controller by using a teaching tool.Place the controller's AUTO/MANU sw

3. XSEL-R/S/RX/SX/RXD/SXD16[4] Default Gateway Setting Set the default gateway to I/O Parameter No.140 to 143.No. Parameter name Default(reference)I

3. XSEL-R/S/RX/SX/RXD/SXD17[7] Number of I/O Port Setting Set the number of ports to be used for I/O Parameters No.14 to 15.Set a number that is a m

3. XSEL-R/S/RX/SX/RXD/SXD183.5.2 Example for Parameter Settings (1) Example for when using EtherNet/IP It is how to establish the setting when using

3. XSEL-R/S/RX/SX/RXD/SXD19No. Parameter name Default(reference)Input Range Unit Remarks 17Network I/F Module 1 Fix-Allocated Output Port Start No.-1

3. XSEL-R/S/RX/SX/RXD/SXD20No. Parameter name Default(reference)Input Range Unit Remarks 234Network I/F Module 2 Extension Output Port Start No.-1-130

3. XSEL-R/S/RX/SX/RXD/SXD21(2) Example for when using EtherNet/IP and I/O Board 1 together It is how to establish the setting when using EtherNet/IP

3. XSEL-R/S/RX/SX/RXD/SXD22No. Parameter name Default(reference)Input Range Unit Remarks 17Network I/F Module 1 Fix-Allocated Output Port Start No.-1

3. XSEL-R/S/RX/SX/RXD/SXD23No. Parameter name Default(reference)Input Range Unit Remarks 234Network I/F Module 2 Extension Output Port Start No.-1-130

Please Read Before Use Thank you for purchasing our product. This Operation Manual describes all necessary information to operate this product safely

3. XSEL-R/S/RX/SX/RXD/SXD24(3) Example for when using EtherNet/IP and I/O Board 1 together This is the setting of when using 192 points of each input

3. XSEL-R/S/RX/SX/RXD/SXD25No. Parameter name Default(reference)Input Range Unit Remarks 17Network I/F Module 1 Fix-Allocated Output Port Start No.-1

3. XSEL-R/S/RX/SX/RXD/SXD26No. Parameter name Default(reference)Input Range Unit Remarks 234Network I/F Module 2 Extension Output Port Start No.-1-130

3. XSEL-R/S/RX/SX/RXD/SXD273.6 Connection to Network EtherNet/IP occupies EtherNet Port No.44818 and 2222. The connection of EtherNet/IP is establish

3. XSEL-R/S/RX/SX/RXD/SXD283.8 I/O Port and Data Reading and Writing The initial setting of SEL language commands for the operation of I/O (input and

3. XSEL-R/S/RX/SX/RXD/SXD29ƔReference How to Read and Write with Swapping Host 8 Bits with Lower 8 Bits for Every 16-Bit Data When conducting reading

4. Appendix304. Appendix 4.1 Troubleshooting (1) In case it is not possible to connect the network, check the current condition on the display of m

4. Appendix31Monitor LED Contents Cause and Remedy EE69EE6C24V I/O Error DO Output Current ErrorIt is generated when the +24V power for I/O is not s

4. Appendix32Ɣ Cold Start Level Errors No. Error name Contents / Counteractions 678Extension I/O Port Assignment Parameter Error There is an error i

4. Appendix334.2 List of EtherNet/IP Related Parameters Ɣ I/O Parameter No. Parameter name Default(reference)Input Range Unit Remarks 1 I/O Port Al

4. Appendix34Ɣ I/O Parameter No. Parameter name Default(reference)Input Range Unit Remarks 124 Network attribute 5 0H0H to FFFFFFFFH-EtherNet TCP/I

4. Appendix35Ɣ I/O Parameter No. Parameter name Default(reference)Input Range Unit Remarks 129 Network attribute 10 0H0H to FFFFFFFFH-EtherNet Oper

4. Appendix36Ɣ I/O Parameter No. Parameter name Default(reference)InputRangeUnit Remarks 149IAI Protocol B/TCP connected destinationIP Address (MANU

4. Appendix37Ɣ I/O Parameter No. Parameter name Default(reference)InputRangeUnit Remarks 225 Network I/F Module Control 7HOnly referring (HEX)-Bit

4. Appendix384.3 Network Setting File It is necessary to use a network setting file dedicated for X-SEL-R/S/RX/SX/RXD/SDX Controllers. Download the f

Change History39Change History Revision Date Description of Revision 2012.09 2013.03 First edition Second edition Pg. 27 Note added for the case Ether



Manual No.: ME0308-2A (March 2013)The information contained in this document is subject to change without notice for purposes of product improvement.C

Table of Contents Safety Guide············································································································ 1 Caution i

1Safety Guide“Safety Guide” has been written to use the machine safely and so prevent personal injury or property damage beforehand. Make sure to read

2No.Operation Description Description 2 Transportation Ɣ When carrying a heavy object, do the work with two or more persons or utilize equipment su

3No.Operation Description Description (2) Cable Wiring Ɣ Use our company’s genuine cables for connecting between the actuator and controller, and for