Iai-america XSEL-KET Uživatelský manuál Strana 152
- Strana / 436
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
133
Part 4 Commands
INTELLIGENT ACTUATOR
SSPG (Pause program)
Command, declaration
Extension condition
(LD, A, O, AB, OB)
Input condition
(I/O, flag)
Command,
declaration
Operand 1 Operand 2
Output
(Output, flag)
Optional Optional SSPG
Program
number
(Program
number)
CC
[Function] Pause the program from the one specified in operand 1 through the other specified in
operand 2, at the current step. Specification in operand 1 only is allowed.
(Note 1) Pausing a program will also pause the operation the program has been executing.
(Note 2) Not only the operation but also the execution of the step itself will be paused.
(Note 3) Main application version 0.20 or earlier only allows specification of one program in operand 1.
[Example 1] SSPG 10 12 Pause program Nos. 10, 11 and 12 at the current step.
Error-generation/output-operation conditions (Main application version 0.21 or later)
When one SSPG program is specified (only operand 1 is specified)
No program number error *1
Program already registered
Status of the
specified program
Program running
Program not
running
Program not yet
registered
Program number
error *1
Error None None
C03
“Non-registered program
specification error”
C2C
“Program number
error”
Output operation ON OFF OFF OFF
* The errors shown in the table represent those that generate in accordance with the status of the specified program.
Errors caused by other factors are excluded.
* 1 --- Program number error indicates specification of a number smaller than 1 or exceeding 64.
When multiple SSPG programs are specified (both operands 1 and 2 are specified)
No program number error *2
Registered program exists inside the
specified range *3
Status of the
specified program
Running program
exists inside the
specified range *4
None of programs
inside the specified
range are running
None of programs inside
the specified range are
registered
Program
number error *1
Error None None
C03
“Non-registered program
specification error”
C2C
“Program
number error”
Output operation ON OFF OFF OFF
* The errors shown in the table represent those that generate in accordance with the status of the specified program.
Errors caused by other factors are excluded.
* 2 --- Program number error indicates specification of a number smaller than 1 or exceeding 64.
* 3 --- In this case, non-registered programs inside the specified range are not treated as a target of operation with
EXPG, ABPG, SSPG and PSPG commands. This will not affect error generation or output operation.
* 4 --- In this case, programs not running (but already registered) inside the specified range are not treated as a
target of operation with SSPG and RSPG commands. This will not affect error generation or output operation.
Program No. 10 Program No. 11
Program No. 12
Currently executed step
Currently executed step
Currently executed step
SSPG
- Seventh Edition 1
- Eighth Edition 1
- Tenth Edition 1
- Please Read Before Use 3
- [Important] 3
- CAUTION 4
- CE Marking 5
- Table of Contents 7
- INTELLIGENT ACTUATOR 10
- Safety Guide 11
- Alert Indication 16
- Introduction 20
- Part 1 Installation 22
- 1. Warranty Period 23
- 2. Scope of Warranty 23
- 3. Scope of Service 23
- 1. Installation Environment 24
- 3. Power Source 25
- 1. Front View of Controller 28
- Battery Capacity: 1000 mAh 30
- Chapter 5 Specifications 38
- 1. Controller Specifications 38
- [Input circuit] 39
- Internal circuit 39
- ON duration 39
- OFF duration 39
- [Output circuit] 40
- The heat output is 63 [W] 44
- 4. External Dimensions 45
- Chapter 6 System Setup 46
- Cable color 48
- 1.3 I/O Flat Cable 50
- PSR-SCP 63
- 24UC/ESA2/4X 63
- 1/1X2/B by 63
- Phoenix 63
- Safety relay 64
- G9S-301 by 65
- Safety IN/OUT 66
- (Refer to 2.2.) 66
- 1. Preparation 71
- 2. Procedure 71
- Chapter 8 Maintenance 76
- Part 2 Operation 81
- Start signal 83
- Emergency-stop 83
- Parameters Parameters 90
- Parameters 90
- Write to flash memory 91
- Write to flash 91
- Caution 100
- 2. Position Part 107
- 3. Command Part 108
- Part 4 Commands 110
- (Count) CP Set zigzag 226 114
- 2. In Alphabetical Order 115
- 1. Commands 120
- Optional Optional MOD 124
- Variable 124
- Data ZR 124
- Optional Optional SQR 127
- Optional Optional AND 128
- Optional Optional OR 129
- Optional Optional EOR 130
- Optional Optional CPXX 131
- Optional Optional TIMC 133
- Program 133
- Prohibited CP 133
- Optional Optional GTTM 134
- (Output 135
- Optional Optional FMIO 143
- Currently paused step 153
- Optional Optional PVEL Speed 161
- Position 161
- Optional Optional PSIZ 165
- X 100 (%) 173
- Optional Optional BASE 176
- Optional Optional GRP 177
- Optional Optional SVXX 185
- Prohibited PE 185
- Optional Optional HOME 186
- Optional Optional MOVP 187
- Optional Optional MOVL 188
- Optional Optional MVPI 189
- Optional Optional MVLI 190
- Start position 191
- Position origin 191
- End position 191
- Optional Optional STOP 193
- Optional Optional PUSH 195
- Optional Optional CHVL 201
- Speed CP 201
- Center angle 202
- Center position 203
- Optional Optional PBND 204
- Distance CP 204
- Optional Optional IFXX 207
- Data CP 207
- Optional Optional DWXX 210
- Optional Optional WHXX 213
- Optional Optional SYST 218
- Optional Optional TMRD 225
- Optional Optional SCHA 227
- Character 227
- Optional Optional SPUT 231
- 1 2 3 . 0 0 0 232
- 87 . 654 232
- Optional Optional STRH 233
- Data CC 233
- Optional Optional SLEN 236
- Optional Optional BGPA 237
- Palletizing 237
- Optional Optional PAPN 238
- Pattern 238
- Optional Optional PAST 240
- (Position 240
- Optional Optional PAPS 241
- Optional Optional PSLI 245
- (Count) CP 245
- Optional Optional PCHZ 246
- Optional Optional ACHZ 249
- ARCD, ARCC, CIRS, ARCS] 263
- 2. PATH/PSPL Commands 265
- 3. CIR/ARC Commands 265
- 1. How to Use 266
- 2. Palletizing Setting 266
- PX-axis direction pitch 269
- Teach position data No. 100 269
- PY-axis direction pitch 269
- 3. Palletizing Calculation 272
- 4. Palletizing Movement 273
- 5. Program Examples 275
- 1. Basic Frame 283
- 2. Ladder Statement Field 284
- 3. Points to Note 284
- 4. Program Example 285
- 1. Operation by Jog Command 286
- [Doll-Picking Game Machine] 286
- Operation Position 287
- I/O Assignments 287
- Operation Flow Chart 287
- [Riveting System] 289
- 3. Palletizing Operation 292
- [Palletizing System] 292
- 293
- Part 5 Multi-Tasking 295
- 2. Multi-Tasking 296
- 5. Program Switching 299
- 1. Equipment 300
- 2. Operation 300
- 4. Hardware 302
- 5. Software 304
- Appendix 306
- Loading capacity 307
- Rated acceleration 307
- [Position table] 311
- 2. Program Format 312
- 6. Path Operation 316
- 8. Circular/Arc Operation 318
- 11. Travel Speed Change 321
- 15. Pause 325
- Input port 20 turns ON 326
- Movement complete signal OFF 328
- Movement complete signal ON 328
- 20. Coordinate Value Output 330
- 21. Conditional Jump 331
- 23. How to Use Offset 333
- Reference point 335
- 26. Jogging 336
- 27. Program Switching 337
- 28. Program Abort 338
- 1 m (1000 mm) 342
- Controller end 342
- Connector not 342
- RD+ 11 RD + SD + 344
- RD- 12 RD - SD 344
- SD+ 15 SD + RD + 344
- SD- 14 SD - RD 344
- 1. Synchro Axes 348
- List of Parameters 354
- 1. I/O Parameters 355
- No. Parameter name 357
- Default value 357
- (Reference) 357
- Input range Unit Remarks 357
- I/O Parameters 362
- PC: PC software 364
- TP: Teaching pendant 364
- FFFFFFFFH 368
- Axis-Specific Parameters 371
- Input range Unit Remarks 376
- (Kelvin = 378
- Input range Unit Remarks 383
- 8. Manual Operation Types 386
- 10. Servo Gain Adjustment 393
- Error Level Control 397
- Error List 399
- Trouble Report Sheet 432
- Change History 433
- 11.12.000 436
Související produkty a manuály pro Hardware Iai-america XSEL-KET
Hardware Iai-america TTA Uživatelský manuál
(85 stránky)
(85 stránky)
Hardware Iai-america XSEL-S Uživatelský manuál
(128 stránky)
(128 stránky)
Hardware Iai-america RCM-GW-DV Uživatelský manuál
(137 stránky)
(137 stránky)
Hardware Iai-america RCM-GW-CC Uživatelský manuál
(132 stránky)
(132 stránky)
Hardware Iai-america RCM-GW-PR Uživatelský manuál
(125 stránky)
(125 stránky)
Hardware Iai-america RCS-C Uživatelský manuál
(119 stránky)
(119 stránky)
Hardware Iai-america E-Con Uživatelský manuál
(111 stránky)
(111 stránky)
Hardware Iai-america PS-24 Uživatelský manuál
(32 stránky)
(32 stránky)
Hardware Iai-america PCON-ABU Uživatelský manuál
(60 stránky)
(60 stránky)
Hardware Iai-america TU-MA96-P Uživatelský manuál
(15 stránky)
(15 stránky)
Hardware Iai-america REXT Uživatelský manuál
(443 stránky)
(443 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 3.339 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce